Answer : As long as motion is being detected ecoLuz shall keep the lights ON. Once the motion stops it will wait for SET time-out period. Time-out period could be set from 23 seconds to 4 minutes. Request for higher or lower Time-out period can also be served for minimum quantity of 100 nos.

Answer : Yes. You can connect either beeper or sounder or fans etc. Output Switch can handle any load upto 5Amp.

Answer : ecoLuz is nearly 5 times more sensitive than available Chinese products in the market. It supports radius of 5 mtrs.

Answer : Yes. Sometimes application needs to switch ON the lights with the slightest motion. For e.g in cabins once the person enters and takes his seat, motion of the person is minimal. However ecoLuz should keep the lights ON as long as cabin is occupied. This feature is not supported by many competitors.

Answer : Yes. Two units can be connected in parallel.

Answer : Fluorescent lights & fans are inductive loads. ecoLuz should be used for inductive loads upto 2.5Amp. For e.g you can connect about 12 40Watts Tubelights & about 3 to 4 fans.

Answer : Lux level at which sensor should start the operation can be SET from full day light to near darkness.

Answer : Lux level at which sensor should start the operation can be SET from full day light to near darkness.

Answer : We are using one of the world's best, finest quality sensor (made in Germany). The product is developed by our own R & D. Product is manufactured with utmost care by our production department & is tested rigorously before packing. Many Chinese versions use poor quality of sensors which results into poor sensitivity and unreliability. Output stage of our circuit is very reliable with almost no failure.

Answer : We recommends using electronic ballast for tubelights. This will not affect life due to frequent switching. With standard choke life may be reduced slightly as life mainly depends upon number of hours of operation.

Answer : Yes. We can make it available for MOQ of 100 nos.

Answer : Yes. Using over-riding mode you can switch ON the lights permanently.

Answer :

ecoLuz	Other Chinese Products
Range is 5 ` 8m radius	Range is 1 ` 2m radius
Operating Voltage 180`260v suitable for Indian conditions	Low supply voltage range
Long relay life due to high quality relay and switching at zero crossing	Random switching hence low life
1 year manufacturer warranty	No manufacturer warranty

Answer : TS230LHB is Standalone Type. TS12LHR can be integrated with Home Automation & Security System provided that these systems have NO & NC contacts.

Answer : Detector is Auto-Resettable.

Answer : The performance of Gas Leak Detector is not measured in terms of range. When gas leaks & the gas particles reach the sensor & when concentration reaches 10% of LEL, warning is given. Hence we recommend to position or place this device as close as possible to the gas source.

Answer : Fully battery operated Gas Leak Detectors are not available anywhere in the world. Reason being the current consumed by such device/ detector/ sensor would drain the standard battery within 6-7 days. Hence it's not practical to keep replacing the batteries after every 7 days. We do not supply battery operated gas leak detector. However we do have model with rechargeable battery backup. In case of power failure this detector with rechargeable battery will switch to battery mode.

Answer : It is not dangerous to have an electrical socket near the gas source. In any typical kitchen there are several electrical home appliances which operate on electricity when connected to the electrical socket like Mixer, Grinder, Fridge, Oven etc. In case of leakage of gas & gas concentration reaching LEL then somebody might switch the power ON/Off, the spark which happens at the switch contact might cause fire. O ur detector gives warning much ahead of dangerous level. Also no switching happens inside the circuit as the circuit is solid state. Hence it's not dangerous to have an electrical socket near the gas source.

Answer : Life of the sensor inside Gas Leak Detector is 2 years. We recommend replacing the gas leak detector after 2 years of use.

Answer :

TrueSafe LPG Gas Leak Detector	Other Chinese Products
Microprocessor based product	Ordinary logic switching
Intelligence avoids false calls	Prone to false calls as non-intelligence
Temperature compensation	No temperature compensation results into false calls at high temperature
Heat Detection feature	No heat detection feature
Kitchen Platform Panel mounting increases its effectiveness by factor of 2	Wall mounting is useful only near cylinder
Wide options available including Bargraph display & flasher	Limited options
Sensor replacement is possible	Manufacturer not accessible hence repair & support is near impossible
1 year manufacturer warranty	No manufacturer warranty

Answer : Life of sensor is about 2 years. However it depends upon the usage. Heavy usage may result in to the lesser sensor life.

Answer : Yes, due to health concern (hygiene), the mouth piece/ pipe need to be changed for every single operation.

Answer : Typically it would cost Rs 2 for Citizen Model & Rs 5 for Police Model.

Answer : In Citizen Model the sensor used is semiconductor sensor. In Police Model the sensor used is Fuel/ Electro-chemical sensor.

Answer : Typically 30-45 seconds warm up time.

Answer : Typically 30-45 seconds warm up time.

Answer : 5 seconds

Answer : The cost for sensor for citizen model is Rs. 2500/-. The cost for sensor for Police model is Rs. 4500/-

Answer :

Cityzen Model	Police Model
Printing Facility - Not Available	Printing Facility - Printer Available
Sensor- Semiconductor Sensor	Sensor- Fuel/ Electro-chemical Sensor
Application For Personal Usage	Application for Police, commercial, security purpose
Sensor Replacement cost = Rs. 2500	Sensor Replacement cost = Rs. 4500
Weight = 64 g Battery excluded	Weight
Dimensions 103×65×27mm (L×W×H)	Dimensions
Non ruggedized Construction	Ruggedized Construction